The Sphero BOLT Power Pack is a portable charging and storage solution for Sphero BOLT robots.

1. It’s available as an all-inclusive kit with 15 robots and accessories.
2. If you already have BOLT’s, it also comes as an empty case.
3. The Power Pack is great for transporting BOLTs between classrooms, storing, and charging.
4. If you’re not using the robots for a few weeks, it’s best to fully charge, turn off, and store them.
5. The case has air vents, cooling fans, and red light notification to prevent overheating.
6. While BOLT robots are waterproof, the Power Pack is not.



If you’re looking for a safe, portable charging and storage solution for Sphero BOLT robots, the BOLT Power Pack is your tool. It is a new addition to the Eduporium store, but may look familiar! It was adapted from the SPRK+ Power Pack except it now supports charging of the Sphero BOLT. This Power Pack holds 15 BOLTs and is available as an all-inclusive set with robots and accessories (charging cradles/cables, protractors, clear turbo covers, maze tape rolls, and stickers) and also as an empty pack for those who already have BOLT robots. Below, you can find some of Sphero’s main tips on how to use, store, cool down, and safely maximize the Power Pack. 



HOW TO USE

1.     Place robots on the charging cradles, plug the power cord in, and turn the power switch on.


2.     The green light on the front of the Power Pack indicates the power is on. The blinking blue cradle lights indicate the robots are charging.


3.     It takes six hours to charge a fully depleted BOLT robot. The blue charger lights will be solid when robots are fully charged. It’s okay to keep robots on the chargers for longer.


4.     Remove BOLT from its cradle for the battery level and robot name to display on the matrix, then connect it to the Sphero Edu app. You can also turn off the Power Pack to see the battery level and robot names for all robots.


5.     If a BOLT can’t connect to the Sphero Edu app, place it in the charging cradle, then tap the button on the side of the cradle. Wait until the animation completes, then try to connect it to the app again.


sphero bolt power pack opened up displaying 15 bolt robots charging inside

HOW TO STORE

If you are not using the robots for a few weeks, it’s best to fully charge them, turn them off, and then store them.


1.     With the Power Pack on, press and hold the cradle button and simultaneously remove the BOLT to turn it off. Repeat for all robots and place them aside. You can also turn off your robot in the settings section of the Sphero Edu app.


2.     Toggle the power switch off and unplug the Power Pack.


3.     Place the robots back inside the Power Pack and store them at room temperature. To turn the robots on after storage, plug them in and turn on the Power Pack. If using robots that have been stored for several months, you may need to recharge the robots.



KEEP IT COOL

Robots may stop charging if they get too warm. If this happens:


1.     The green light on the Power Pack will change to red and the blue charging cradle lights will turn off, indicating that the robots have stopped charging.


2.     Open the lid and allow the Power Pack to cool; the fans will continue to run.


3.     Once cooled, the red light will change back to green and the charging cradle lights will turn back on to indicate the robots have resumed charging.


4.     If overheating occurs often, move the Power Pack to a cooler room and keep the lid open while charging.


sphero bolt power pack with accessories



KEEP IT SAFE

Avoid these actions to ensure safe use and long life of your Power Pack.


1.     DO NOT charge non-BOLT robots with this Power Pack. Do not charge BOLT robots on non-BOLT cradles.


2.     DO NOT touch robots when the Power Pack is overheated because the robots could be hot.


3.     DO NOT cover air vents. This could cause the Power Pack to overheat and damage the robots.


4.     DO NOT submerge or spray water on the Power Pack. The robots are waterproof, but the Power Pack is not.


5.     DO NOT disassemble the Power Pack.


6.     DO NOT use the Power Pack if the power supply is damaged.


7.     DO NOT use an extension cord between the power supply and the wall outlet. Make sure the power cord is safely placed to avoid tripping or cord damage.



Whether you’re already using the Sphero BOLT Power Pack or are looking for insight on whether it is the right solution for your classroom, we hope this blog gave you some helpful tips for moving forward! If you have any questions about the Power Pack, BOLT robot, or other Sphero products on our store (see below), please reach out to us. And, be sure to follow us on Instagram and Twitter as well for more EdTech Tips & Tricks!